Skid Plate Protection For the Oil Pan!

This relatively simply oil pan modification, though it’s being done on Project CJ-7, can be installed on almost ANY 4×4 with an exposed oil pan.  Though it may be a rare event to poke a hole in your oil pan, it can happen.  At the very least it offers protection from rocks that might chip away the paint and can lead to rust down the road.  

Although this Project CJ-7’s engine is a very young crate 360 (approx 14k on it), the parts bolted onto the engine were most likely off of the original Jeep Grand Cherokee.  One of the last things that needed attention on the engine was the oil pan.  Because it was easier to remove it while it on the frame, I waited until the engine was in before dropping the pan.  My main concern was that the visible rust may have eaten too much metal off the pan to salvage it.  Once I dropped it off and cleaned it up it turned out not to be too bad.  Mostly pitted surface rust.   Nothing that some Corroless couldn’t neutralize.

Special note on Coroless Rust Inhibitor…
Since the writing of this page, Corroless is now marketed as a product called Eastwood Rust Encapsulator.  Same product, same distributor, different name.

So first thing was to wire-wheel the outside pretty good and wash it down with Simple Green to prep it for paint.

Secondly I made sure the bolt holes were on an even plain.  What mean by that is this: when a leak is detected in the oil pan, what the first thing guys do?  Tighten the bolt down right?  Over time the bolt holes in the pan become recessed due to tightening them down too tight, one too many times.   To get a good seal you need to have a flat contact area across the entire seal.   So with a small hammer I flattened the holes that appeared to have been tightened down too hard.

With it clean and in good shape, it got a coat of Corroless Rust inhibitor.


Protection for the Vitals

I pondered how I could install a skid plate to protect probably the most important spot on the Jeep, it’s oil pan.  One good whack of a sharp rock and I could loose the life blood of the engine.  Not good.  So coming up with a Skid Plate was a very good idea.

There really is no good way to bolt up a skid plate but a better idea was to attach one to the pan itself.  I thought about welding it to it.  But I thought a whack to the skid plate might rip the weld and create a hole anyway. Plus welding thin steel is hard without burning a hole in it.  Then I thought of a idea that could possibly work even better using some of the best stuff around.  Silicone. Why not simply glue the skid plate on with Silicone.  Having used it in the past in construction applications I know silicone has tremendous surface tension and using it as a glue would work well.

So I set off to create a skid plate that would not just cover the lowest part of the oil pan but the entire underside of the oil pan.  I got the width of the pan plus the totaled length of pan running across the flat areas from front to back.

Using 14 gauge steel, I cut the rectangle, then bent it to conform to the shape of the pan as close as possible.  I bent it by creating a make-shift “bending brake” with angle iron and C-clamps (see picture below).  To form around the drain plug, I used a small 5 pound sledge to create a relief bend around the plug large enough to fit a socket over the drain plug (see pictures below).

Angle iron c-clamped on the stock for leverage.

How the bends were made in the skid plate:

Forming the drain plug relief bend in the skid plate:

Test for clearance of a socket:

Test fit: 

A bend was made too sharp, so to flatten out the bend a little I used a section of railroad rail as an anvil and a sledge to flatten it out:

Next step, I oozed out about an entire tube of GE 50 year Silicone across the areas where the pan metal will meet the skid metal (see picture). Electrical tape was placed over the drain plug to keep it clean of silicone.  Then the silicone was worked onto the surface so it covered the whole area it was supposed to cover, not just where it when on from the tube.  This increases the surface tension and will help it to “stick” to the oil pan very well.

Then the skid plate was pressed into the silicone and excess was used to cover the sides.  Then additional silicone was put on the sides to actually add more protection to the oil pans exposed sides.  This should act as a protective cover to deflect rocks and prevent chips and rust down the road as well as possible preventing direct damage.






With adequate time to dry the oil pan was then re-installed with new seals and sealant as well as stainless steel hardware. 

Once dry, it would be VERY hard to remove this skid plate even if you were using tools.  Don’t under-estimate the holding power of a two foot square area of silicone sealant.  A side benefit of using silicone is that if the skid plate ever took a whack, silicone will flex and absorb the shock of an impact.  Over all this skid plate cost only about 20 bucks and that includes buying a new gasket for the skid plate. Minus the gasket and it’s really just the cost of paint and the silicone.   That’s about six bucks at Walmart providing you have a source for free scrap metal.   You can’t beat that for insurance on a vital organ of your vehicle.

Project CJ-7 Articles

Project Jeep CJ-7

Project Jeep CJ-7 Specs & Mods

August 6, 2017 0

The budget Rebuild by Ralph HasselThe complete build is documentedhere on www.Offroaders.comThis 1978 Jeep CJ-7 never started life as a complete Jeep; rather it was built completely from parts. The goal was to build a […]

Project Jeep CJ-7

Skid Plate Protection For the Oil Pan!

August 2, 2017 0

This relatively simply oil pan modification, though it’s being done on Project CJ-7, can be installed on almost ANY 4×4 with an exposed oil pan.  Though it may be a rare event to poke a […]

Project Jeep CJ-7

Fabricating an Armored Jeep Skid Plate

August 1, 2017 0

This Project CJ-7 article is about converting and armoring a Dana 300 skid plate to work with a Dana 20 transfer case.  An ounce of prevention is worth a few pounds of steel.  After hearing stories […]

Project Jeep CJ-7

T18A Clutch Fork Modifications

August 1, 2017 0

In swapping the T-18A onto this Jeep project, a good tip was passed onto me from Mike of  This tip has to do with the stock clutch fork being used in the stock bell […]

Project Jeep CJ-7

Project CJ-7 gets Armored Custom U-Bolt Plates

June 23, 2017 0

Fabricating Custom U-Bolt Plates with Skid Protection for Project Jeep CJ-7   With the job of a Dana 44 axle swap to the project CJ-7 came the need for new u-bolt plates.  Two things made stock u-bolt […]

Project Jeep CJ-7

CJ Flipping the Tie Rod & Drag Link

June 21, 2017 2

A Simple yet very effective method of protecting your tie rod from impact with rocks and things, is to raise the tie rod up.  Raising the Drag link also reduces bump-steer, a side effect of […]

Project Jeep CJ-7

Project Jeep CJ-7 Radiator Protection

June 13, 2017 0

Using 6 bucks worth of material to protect a 300 dollar 3-core radiator and to cool the V8 Engine. When looking at the grill of my 78 CJ-7, the one thing that just stuck out like […]

Project Jeep CJ-7

Project CJ-7 gets a T-18A Borg-Warner Transmission

June 5, 2017 0

After doing some research I finally decided to look for a Borg-Warner T-18A manual transmission.  Manual because that is what I prefer.   The T-18A because of it’s 6.32:1 first gear and it’s heavy duty, cast […]

Project Jeep CJ-7

Jeep CJ-7 Swaybar Bracket Upgrade

May 17, 2017 0

Project Jeep CJ-7 Daystar Swaybar Bushings Tip.  When swapping out your stock CJ swaybar bushings with the Daystar Swaybar Bushings, here’s a Tip – Use the CJ bracket!  Here’s why…First off, upgrading your sway bar bushings […]

Project Jeep CJ-7

Jeep CJ Dana 44 Front Axle Swap

May 12, 2017 0

Project Jeep CJ-7 – Disassembling the Scout II  Dana 44 Front Axle.  After acquiring the Dana 44 axles I also picked up a Dana 30 narrow track front axle that was in great shape.  The […]

Project Jeep CJ-7

Dana 44 Rear Axle Swapped onto a CJ-7 Frame

May 12, 2017 0

Continuing on from the front axle prep, the rear axle’s spring pad angle recorded and spring pads were removed.  That was followed up by an inspection of differential and rear drum brakes to make sure […]

Project Jeep CJ-7

Front Spring Hangers

May 9, 2017 0

Project Jeep CJ-7   Scout II Dana 44 Axles Swap onto a CJ-7 FrameNew Custom Fabricated HangersFront Springs – Front HangersThe front hangers were a little easier to design than the rear hangers.  Mainly because they […]

Project Jeep CJ-7

Painting the Hangers

May 9, 2017 0

Project Jeep CJ-7   Scout II Dana 44 Axles Swap onto a CJ-7 FrameFabricated Leaf Spring HangersInstalling the Front Leaf Springs HangersBelow is the whole set of hangers.  Gussets have been welded in and all the holes […]

Project Jeep CJ-7

Custom U-Bolt Plates with Skid Protection

May 9, 2017 0

Project Jeep CJ-7   U-Bolt Skid PlatesFabricating Custom U-Bolt Plates with Skid ProtectionWith the job of a Dana 44 axle swap to the project CJ-7, came the need for new u-bolt plates.  Two things made stock […]