Saginaw Steering Gearbox Mounting Bracket | Offroaders.com
Offroaders.com

Saginaw Steering Gearbox Mounting Bracket

Project Jeep CJ-7 – Installation of a Saginaw Gearbox

Mounting a Gearbox Bracket That Means Business!

With the installation of an AGR Superbox 2 and an AGR High Performance Power Steering pump to turn my Super Swampers, I could no longer trust my stock bracket to hold the Saginaw gearbox onto the frame.  So I made a call to my friend Mike at OK Four Wheel drive and asked about a power steering gearbox mounting bracket that I had heard about.

Besides the seriously beefy construction, this bracket moves the steering box 1 inch forward which would give me the extra room I needed to clear my pitman arm from my tie rod.  Then I could get rid of my pitman arm hack job.  Mike hooked me up with this SERIOUS aftermarket Saginaw Gearbox mount.  When you compare this massive bracket to the stock CJ two piece stamped steel, there not even in the same ballpark.   Laser cut 3/8″ steel.  Serious beef. I’m not sure about the manufacturer of this bracket, apparently it’s from a small mid-west shop, but I ordered from OK Four wheel Drive in Stewartsville New Jersey (www.ok4wd.com, 908-454-6973).  If you give them a call and ask for Mike, tell him Ralph sent you and ask for the CJ Saginaw gearbox mounting bracket that I bought. 

Here are a few pictures of comparison between  the stock CJ, stamped steel Saginaw mounting bracket on the left and the new, larger aftermarket Saginaw gearbox mounting bracket.  A few things to note about this new heavy duty bracket are: the diameter of the steel it is fabricated from, 1/4″ and 3/8″ steel welded together and gusseted. The top horizontal piece of the bracket has more surface area with a third bolt hole for an additional 7/16″ bolt.  Also the new mounting bracket moves my Saginaw gearbox one inch forward with fixes the issue of my pitman arm hitting the tie rod on compression of the driver side suspension.  A plus for this bracket is that it is a bolt on minus a little trimming of the front frame cross member to clear the Saginaw gearbox hoses (see below).

First order of business with the bracket is to give the bare metal a paint job.  I thought it would be a crime to paint this massive bracket anything but a bright color so I chose red.  Then the AGR Saginaw gearbox was bolted up to the bracket using the spacers that came with the bracket.  I replaced the hardware that the AGR gearbox came with, which was grade 5 hardware.  As with everything else on the Jeep, I used grade  8 hardware instead.


Because this bracket moves the box forward about one inch, I had to notch the frame crossmember a little.  These next three shots point out where I had to trim a small notch in the CJ-7’s front cross member to clear the AGR Superbox 2 power steering fluid hoses.      

I used my angle grinder to notch the frame just enough to be able to get the hoses on without any contact.     
I trimmed the notch a few times in between test fitting the AGR and bracket to the frame.     


Finally with enough clearance to install the hoses I mounted the AGR gearbox and the new gearbox mounting bracket to the frame using grade 8 bolts.

The following are a few pictures of the gearbox and bracket mounted up.

    



An underside view

This picture shows the extra clearance I gained by moving the steering box one inch forward.

AGR Pump Installed

The Good the bad and the ugly.

The Good.  So what do I think of it?  Massive.  Super strong.  It won’t be this bracket that breaks I can tell you that.  Moving the gearbox one inch forward was a huge plus for me.  I needed the room with the Dana 44 axle and the aftermarket tie rod and drag link causing contact.  The extra room will be helpful if I ever go with a reverse shackle.

The Bad.  Not much bad.  It is a little on the expensive side at 150 bucks but after thinking of a way to fabricate my own, it saved me a lot of trial and error and headaches.

The Ugly.  Yeah, I like ugly.  This thing is so massive that you don’t want to hide it.  Paint it bright red like an in-grown toe nail.

The Pitman arm hack

Above, my hack job to eliminate contact between the tie rod and the pitman arm.  Note, DON’T DO THIS!  It was a temporary hack job to move the Jeep around. The Jeep now had a new factory pitman on the AGR Steering Gear.



Project CJ-7 Articles

Project Jeep CJ-7

Project Jeep CJ-7 Specs & Mods

August 6, 2017 0

The budget Rebuild by Ralph HasselThe complete build is documentedhere on www.Offroaders.comThis 1978 Jeep CJ-7 never started life as a complete Jeep; rather it was built completely from parts. The goal was to build a […]

Project Jeep CJ-7

Skid Plate Protection For the Oil Pan!

August 2, 2017 0

This relatively simply oil pan modification, though it’s being done on Project CJ-7, can be installed on almost ANY 4×4 with an exposed oil pan.  Though it may be a rare event to poke a […]

Project Jeep CJ-7

Fabricating an Armored Jeep Skid Plate

August 1, 2017 0

This Project CJ-7 article is about converting and armoring a Dana 300 skid plate to work with a Dana 20 transfer case.  An ounce of prevention is worth a few pounds of steel.  After hearing stories […]

Project Jeep CJ-7

T18A Clutch Fork Modifications

August 1, 2017 0

In swapping the T-18A onto this Jeep project, a good tip was passed onto me from Mike of www.Jeepfan.com.  This tip has to do with the stock clutch fork being used in the stock bell […]

Project Jeep CJ-7

Project CJ-7 gets Armored Custom U-Bolt Plates

June 23, 2017 0

Fabricating Custom U-Bolt Plates with Skid Protection for Project Jeep CJ-7   With the job of a Dana 44 axle swap to the project CJ-7 came the need for new u-bolt plates.  Two things made stock u-bolt […]

Project Jeep CJ-7

CJ Flipping the Tie Rod & Drag Link

June 21, 2017 0

A Simple yet very effective method of protecting your tie rod from impact with rocks and things, is to raise the tie rod up.  Raising the Drag link also reduces bump-steer, a side effect of […]

Project Jeep CJ-7

Project Jeep CJ-7 Radiator Protection

June 13, 2017 0

Using 6 bucks worth of material to protect a 300 dollar 3-core radiator and to cool the V8 Engine. When looking at the grill of my 78 CJ-7, the one thing that just stuck out like […]

Project Jeep CJ-7

Project CJ-7 gets a T-18A Borg-Warner Transmission

June 5, 2017 0

After doing some research I finally decided to look for a Borg-Warner T-18A manual transmission.  Manual because that is what I prefer.   The T-18A because of it’s 6.32:1 first gear and it’s heavy duty, cast […]

Project Jeep CJ-7

Jeep CJ-7 Swaybar Bracket Upgrade

May 17, 2017 0

Project Jeep CJ-7 Daystar Swaybar Bushings Tip.  When swapping out your stock CJ swaybar bushings with the Daystar Swaybar Bushings, here’s a Tip – Use the CJ bracket!  Here’s why…First off, upgrading your sway bar bushings […]

Project Jeep CJ-7

Jeep CJ Dana 44 Front Axle Swap

May 12, 2017 0

Project Jeep CJ-7 – Disassembling the Scout II  Dana 44 Front Axle.  After acquiring the Dana 44 axles I also picked up a Dana 30 narrow track front axle that was in great shape.  The […]

Project Jeep CJ-7

Dana 44 Rear Axle Swapped onto a CJ-7 Frame

May 12, 2017 0

Continuing on from the front axle prep, the rear axle’s spring pad angle recorded and spring pads were removed.  That was followed up by an inspection of differential and rear drum brakes to make sure […]

Project Jeep CJ-7

Front Spring Hangers

May 9, 2017 0

Project Jeep CJ-7   Scout II Dana 44 Axles Swap onto a CJ-7 FrameNew Custom Fabricated HangersFront Springs – Front HangersThe front hangers were a little easier to design than the rear hangers.  Mainly because they […]

Project Jeep CJ-7

Painting the Hangers

May 9, 2017 0

Project Jeep CJ-7   Scout II Dana 44 Axles Swap onto a CJ-7 FrameFabricated Leaf Spring HangersInstalling the Front Leaf Springs HangersBelow is the whole set of hangers.  Gussets have been welded in and all the holes […]

Project Jeep CJ-7

Custom U-Bolt Plates with Skid Protection

May 9, 2017 0

Project Jeep CJ-7   U-Bolt Skid PlatesFabricating Custom U-Bolt Plates with Skid ProtectionWith the job of a Dana 44 axle swap to the project CJ-7, came the need for new u-bolt plates.  Two things made stock […]