Dana 44 Rear Axle Swapped onto a CJ-7 Frame | Offroaders.com
Offroaders.com

Dana 44 Rear Axle Swapped onto a CJ-7 Frame

Continuing on from the front axle prep, the rear axle’s spring pad angle recorded and spring pads were removed.  That was followed up by an inspection of differential and rear drum brakes to make sure there wasn’t anything catastrophic that would make the axle unusable or unrepairable. Everything looked good.

By clamping a piece of angle iron to the spring pad I was able to measure the angle off of a flat surface on the housing.  When re-welding the new, wider, and stronger spring pads to the housing I planned to tilt the pinion angle higher towards the output of the transfer case, however I still wanted the angle location of the old pads as a reference if only for comparison.

Spring Pads cut off.  Ready to be cleaned and painted.  Before power washing the axles, I took a wire wheel on the angle grinder to both axles.  This was a very messy job.  Dust from the surface rust and dirt was everywhere.  I used a respirator to breath easier.  It was worth it though.  When it came to power washing the axles, they cleaned up very well with most of the surfaces rust and dirt gone.  Also I soaked both axles in Simple Green after wire wheeling them to break down the oil and grease for a better surface to prime and paint.

Project CJ-7 Articles

Project Jeep CJ-7

Project Jeep CJ-7 Specs & Mods

August 6, 2017 0

The budget Rebuild by Ralph HasselThe complete build is documentedhere on www.Offroaders.comThis 1978 Jeep CJ-7 never started life as a complete Jeep; rather it was built completely from parts. The goal was to build a […]

Project Jeep CJ-7

Skid Plate Protection For the Oil Pan!

August 2, 2017 0

This relatively simply oil pan modification, though it’s being done on Project CJ-7, can be installed on almost ANY 4×4 with an exposed oil pan.  Though it may be a rare event to poke a […]

Project Jeep CJ-7

Fabricating an Armored Jeep Skid Plate

August 1, 2017 0

This Project CJ-7 article is about converting and armoring a Dana 300 skid plate to work with a Dana 20 transfer case.  An ounce of prevention is worth a few pounds of steel.  After hearing stories […]

Project Jeep CJ-7

T18A Clutch Fork Modifications

August 1, 2017 0

In swapping the T-18A onto this Jeep project, a good tip was passed onto me from Mike of www.Jeepfan.com.  This tip has to do with the stock clutch fork being used in the stock bell […]

Project Jeep CJ-7

Project CJ-7 gets Armored Custom U-Bolt Plates

June 23, 2017 0

Fabricating Custom U-Bolt Plates with Skid Protection for Project Jeep CJ-7   With the job of a Dana 44 axle swap to the project CJ-7 came the need for new u-bolt plates.  Two things made stock u-bolt […]

Project Jeep CJ-7

CJ Flipping the Tie Rod & Drag Link

June 21, 2017 0

A Simple yet very effective method of protecting your tie rod from impact with rocks and things, is to raise the tie rod up.  Raising the Drag link also reduces bump-steer, a side effect of […]

Project Jeep CJ-7

Project Jeep CJ-7 Radiator Protection

June 13, 2017 0

Using 6 bucks worth of material to protect a 300 dollar 3-core radiator and to cool the V8 Engine. When looking at the grill of my 78 CJ-7, the one thing that just stuck out like […]

Project Jeep CJ-7

Project CJ-7 gets a T-18A Borg-Warner Transmission

June 5, 2017 0

After doing some research I finally decided to look for a Borg-Warner T-18A manual transmission.  Manual because that is what I prefer.   The T-18A because of it’s 6.32:1 first gear and it’s heavy duty, cast […]

Project Jeep CJ-7

Jeep CJ-7 Swaybar Bracket Upgrade

May 17, 2017 0

Project Jeep CJ-7 Daystar Swaybar Bushings Tip.  When swapping out your stock CJ swaybar bushings with the Daystar Swaybar Bushings, here’s a Tip – Use the CJ bracket!  Here’s why…First off, upgrading your sway bar bushings […]

Project Jeep CJ-7

Jeep CJ Dana 44 Front Axle Swap

May 12, 2017 0

Project Jeep CJ-7 – Disassembling the Scout II  Dana 44 Front Axle.  After acquiring the Dana 44 axles I also picked up a Dana 30 narrow track front axle that was in great shape.  The […]

Project Jeep CJ-7

Dana 44 Rear Axle Swapped onto a CJ-7 Frame

May 12, 2017 0

Continuing on from the front axle prep, the rear axle’s spring pad angle recorded and spring pads were removed.  That was followed up by an inspection of differential and rear drum brakes to make sure […]

Project Jeep CJ-7

Front Spring Hangers

May 9, 2017 0

Project Jeep CJ-7   Scout II Dana 44 Axles Swap onto a CJ-7 FrameNew Custom Fabricated HangersFront Springs – Front HangersThe front hangers were a little easier to design than the rear hangers.  Mainly because they […]

Project Jeep CJ-7

Painting the Hangers

May 9, 2017 0

Project Jeep CJ-7   Scout II Dana 44 Axles Swap onto a CJ-7 FrameFabricated Leaf Spring HangersInstalling the Front Leaf Springs HangersBelow is the whole set of hangers.  Gussets have been welded in and all the holes […]

Project Jeep CJ-7

Custom U-Bolt Plates with Skid Protection

May 9, 2017 0

Project Jeep CJ-7   U-Bolt Skid PlatesFabricating Custom U-Bolt Plates with Skid ProtectionWith the job of a Dana 44 axle swap to the project CJ-7, came the need for new u-bolt plates.  Two things made stock […]