CJ Flipping the Tie Rod & Drag Link | Offroaders.com
Offroaders.com

CJ Flipping the Tie Rod & Drag Link

A Simple yet very effective method of protecting your tie rod from impact with rocks and things, is to raise the tie rod up.  Raising the Drag link also reduces bump-steer, a side effect of a suspension lift might experience when the drag link is put on a harder angle between the passenger side knuckle and the steering box.  Flipping the drag link on the knuckle reduces this angle.  This article shows a method of flipping the drag link and tie rod on a CJ-7 using the stock outer knuckles.

There are a few different methods of flipping the tie rod and drag link that I am aware of.  One of the cheapest and easiest methods is to ream the ball joint holes and place a cone specifically designed for this purpose which are available from some 4×4 shops and vendors.  If you’re interesting in a set of 3 cones, I have a few sets for sale. Contact me.  You’ll also need a reamer.

How It’s Done (how I did it anyway)…

With the front axle disassembled, now was a good time to take care of flipping the tie rod.  For easy access I clamped the outer knuckles in the vice but it can just as easily be done on the vehicle.  In a nutshell what I’m doing is reversing the taper of the hole that the tie rod ends pass though.   The idea is to ream the hole from the top down but only go half way down.  The cones, which are inserted from the bottom up, make up the rest of the taper and essentially reverse the taper so that its wider at the top and narrower at the bottom.

Below you will see the stock ball joint in place as it would be in it’s stock location.


I took the reamer and placed it in the existing hole from the bottom up. Then I and made a depth mark with a black marker.  This will indicate the depth of the hole the reamer will make from the top down.

Then, from the top down, start drilling with the reamer.  I used a hand drill to take out most of the material I wanted to remove using the drill. Then, so I didn’t drill too far I did the final small amount by hand.  The last thing you want to do is drill out too much material.

Project CJ-7 Articles

Project Jeep CJ-7

Project Jeep CJ-7 Specs & Mods

August 6, 2017 0

The budget Rebuild by Ralph HasselThe complete build is documentedhere on www.Offroaders.comThis 1978 Jeep CJ-7 never started life as a complete Jeep; rather it was built completely from parts. The goal was to build a […]

Project Jeep CJ-7

Skid Plate Protection For the Oil Pan!

August 2, 2017 0

This relatively simply oil pan modification, though it’s being done on Project CJ-7, can be installed on almost ANY 4×4 with an exposed oil pan.  Though it may be a rare event to poke a […]

Project Jeep CJ-7

Fabricating an Armored Jeep Skid Plate

August 1, 2017 0

This Project CJ-7 article is about converting and armoring a Dana 300 skid plate to work with a Dana 20 transfer case.  An ounce of prevention is worth a few pounds of steel.  After hearing stories […]

Project Jeep CJ-7

T18A Clutch Fork Modifications

August 1, 2017 0

In swapping the T-18A onto this Jeep project, a good tip was passed onto me from Mike of www.Jeepfan.com.  This tip has to do with the stock clutch fork being used in the stock bell […]

Project Jeep CJ-7

Project CJ-7 gets Armored Custom U-Bolt Plates

June 23, 2017 0

Fabricating Custom U-Bolt Plates with Skid Protection for Project Jeep CJ-7   With the job of a Dana 44 axle swap to the project CJ-7 came the need for new u-bolt plates.  Two things made stock u-bolt […]

Project Jeep CJ-7

CJ Flipping the Tie Rod & Drag Link

June 21, 2017 0

A Simple yet very effective method of protecting your tie rod from impact with rocks and things, is to raise the tie rod up.  Raising the Drag link also reduces bump-steer, a side effect of […]

Project Jeep CJ-7

Project Jeep CJ-7 Radiator Protection

June 13, 2017 0

Using 6 bucks worth of material to protect a 300 dollar 3-core radiator and to cool the V8 Engine. When looking at the grill of my 78 CJ-7, the one thing that just stuck out like […]

Project Jeep CJ-7

Project CJ-7 gets a T-18A Borg-Warner Transmission

June 5, 2017 0

After doing some research I finally decided to look for a Borg-Warner T-18A manual transmission.  Manual because that is what I prefer.   The T-18A because of it’s 6.32:1 first gear and it’s heavy duty, cast […]

Project Jeep CJ-7

Jeep CJ-7 Swaybar Bracket Upgrade

May 17, 2017 0

Project Jeep CJ-7 Daystar Swaybar Bushings Tip.  When swapping out your stock CJ swaybar bushings with the Daystar Swaybar Bushings, here’s a Tip – Use the CJ bracket!  Here’s why…First off, upgrading your sway bar bushings […]

Project Jeep CJ-7

Jeep CJ Dana 44 Front Axle Swap

May 12, 2017 0

Project Jeep CJ-7 – Disassembling the Scout II  Dana 44 Front Axle.  After acquiring the Dana 44 axles I also picked up a Dana 30 narrow track front axle that was in great shape.  The […]

Project Jeep CJ-7

Dana 44 Rear Axle Swapped onto a CJ-7 Frame

May 12, 2017 0

Continuing on from the front axle prep, the rear axle’s spring pad angle recorded and spring pads were removed.  That was followed up by an inspection of differential and rear drum brakes to make sure […]

Project Jeep CJ-7

Front Spring Hangers

May 9, 2017 0

Project Jeep CJ-7   Scout II Dana 44 Axles Swap onto a CJ-7 FrameNew Custom Fabricated HangersFront Springs – Front HangersThe front hangers were a little easier to design than the rear hangers.  Mainly because they […]

Project Jeep CJ-7

Painting the Hangers

May 9, 2017 0

Project Jeep CJ-7   Scout II Dana 44 Axles Swap onto a CJ-7 FrameFabricated Leaf Spring HangersInstalling the Front Leaf Springs HangersBelow is the whole set of hangers.  Gussets have been welded in and all the holes […]

Project Jeep CJ-7

Custom U-Bolt Plates with Skid Protection

May 9, 2017 0

Project Jeep CJ-7   U-Bolt Skid PlatesFabricating Custom U-Bolt Plates with Skid ProtectionWith the job of a Dana 44 axle swap to the project CJ-7, came the need for new u-bolt plates.  Two things made stock […]